• ParanoidPizzas@aussie.zone
    link
    fedilink
    arrow-up
    13
    ·
    1 year ago

    When I was 15, my dad purchased me a plaster saw (still have it) and handed me his drill.

    Then told me to make it look neat, but “don’t fuck up because your mother will kill us both”.

    I ran about 4 network points through the house.

    Nothing like fear to produce a 100% perfect finish 😉

    • TehDreamer@lemmy.ml
      link
      fedilink
      arrow-up
      6
      ·
      1 year ago

      And then there’s me who just screwed up installing a new door knob. I stripped the threads on the screws cause I used the wrong size screws drilling. Now if the new knob fails in the future, I need to buy a new door lmao

      • helixdaunting@lemm.ee
        link
        fedilink
        arrow-up
        4
        ·
        1 year ago

        If it’s a wooden door that you’re screwing into, dab some match sticks with a little bit of liquid nails and gently hammer them into the stripped-out screw hole, and cut them flush with the hole. Once the glue dries, you can drive the screw back into the matches and it’ll have enough wood to bite into.

      • Lifter@discuss.tchncs.de
        link
        fedilink
        arrow-up
        2
        ·
        1 year ago

        If you can, re-use existing sockets! Old telephone or antenna lines can work! You tie the cable to the end of the old cable and pull it through the existing PVC pipe.

        • ccunix@lemmy.world
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          That’s exactly what I am about to do in the house we’re signing for in few weeks (waiting for the attorney to give us an appointment).

          When I saw the phone jack’s in every room, all terminating down in the garage, I just figured it would be rude not too. Seeing as we will have 2Gb fibre, it makes sense

  • thehatfox@lemmy.world
    link
    fedilink
    arrow-up
    3
    ·
    1 year ago

    A tale as old as time. Before Ethernet cables we were running phone extension cables through the house to connect up the modem to the only phone jack.

  • A_Random_Idiot@lemmy.world
    link
    fedilink
    arrow-up
    3
    ·
    1 year ago

    I did this for every device in my house. used flat ethernet cable and just fished it under the carpets. Was significantly cheaper than trying to make wireless reach the other side of the house.

      • Rannoch@lemm.ee
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        Yeah they’re great! I got a super long flat white one and those little white plastic staple things you can lightly hammer into the wall, and ran it along the baseboard of the walls, makes it nearly invisible! It was a bit tedious to do (which is why I haven’t yet redone it in the place I live now, although I will), but honestly I super recommend it. My partner wanted to try and run cords through the walls but I was way too nervous about what might go wrong, so found this solution instead lol

      • panda_paddle@lemmy.world
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        You can also buy devices you plug into the wall and route your network through your power network. Used them to give my detached garage wifi. Works pretty well.

        • Fordry@lemmy.world
          link
          fedilink
          arrow-up
          3
          ·
          1 year ago

          Can be unreliable though based on what else is on the circuit. Had a portable ac that completely took my power line ethernet connection out whenever it ran.

        • Glork@lemmy.world
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          Based on my research, you get the speed of 2.4 ghz wireless (which while it works, it could be better) with the inconvenience of having to use a cable. Performance also depends on wire insulation, which often isn’t built for running PLC. However, you can’t beat the “plug-and-play” of wired there, which might be attractive.

          I’d recommend getting a mesh router setup, gives you 5ghz wireless over the whole house (assuming proper setup), and some mesh points support wired output (effectively having a wireless bridge)

  • Gojiras_Rage@lemmy.world
    link
    fedilink
    arrow-up
    2
    ·
    1 year ago

    I had to buy carpets to hide the cable under them when running across the floor. Only exposed parts go through the doorways, and the wife complains about them. Well, I am not complaining about our craptastic wifi anymore.

    • teft@lemmy.world
      link
      fedilink
      arrow-up
      1
      ·
      1 year ago

      If you own your house you could learn to pull cable and how to do punchdowns. It’s not a super difficult job. That way you could impress the lady of the house with your technical skills while also hiding the mess.

      • jdaxe@infosec.pub
        link
        fedilink
        arrow-up
        0
        ·
        1 year ago

        I’d be careful giving broad advice like this.

        In my country (Australia) it’s illegal to run cabling yourself unless you’re a registered cabler.

          • stevestevesteve@lemmy.world
            link
            fedilink
            arrow-up
            1
            ·
            1 year ago

            I seem to remember that yes, it was even for low voltage data cabling.

            Not that I would imagine anyone’s enforcing it strongly

              • Squeak@lemmy.world
                link
                fedilink
                arrow-up
                0
                ·
                1 year ago

                Would they be able to prove it wasn’t installed by a licensed contractor? Ok, if you have it installed legally then you’ll likely have an invoice/receipt, but if you lose it that doesn’t mean the cable is illegal. So if you did it yourself, how would they know it’s not just a case of a missing invoice?

                • dustojnikhummer@lemmy.world
                  link
                  fedilink
                  arrow-up
                  1
                  ·
                  1 year ago

                  I’m not saying it would go anywhere, but with how scummy insurance companies are they might try it. Still, it’s a bullshit law

  • Aceticon@lemmy.world
    link
    fedilink
    arrow-up
    1
    ·
    edit-2
    1 year ago

    You could just use 2 Ethernet Over Power adaptors (not to be confused with power over ethernet).

    After all, it’s not as if the powerlines aren’t already installed at home and connect all power plugs with all other power plugs.

    This isn’t even new: I’ve been using this solution for about a decade, back when it could do a mere 20Mb/s (which was still way faster than my Internet connection could handle back then ;))

    Unless having a 500Mb/s limit on bandwith is somehow unacceptable when you could have Gigabit ethernet. Then again, why not fibre all the way ;)

    • Entheogen@lemmy.world
      link
      fedilink
      arrow-up
      0
      ·
      1 year ago

      Have you ever paid attention to packet loss?

      Honest question, because I’m an electrician and Ethernet is so fickle, I’ve always assumed it would play hell on the overall quality.

      • Fordry@lemmy.world
        link
        fedilink
        arrow-up
        1
        ·
        edit-2
        1 year ago

        It definitely can be finicky. I had a portable ac that completely killed the power line ethernet connection when it ran. And my current house I have it in i use from where my router is to where my main TV is and it is unreliable even without that AC unit. So it definitely depends on the circumstances.

      • Aceticon@lemmy.world
        link
        fedilink
        arrow-up
        1
        ·
        edit-2
        1 year ago

        The whole thing is layered into multiple levels (go check the OSI Model and its Layers on Wikipedia if you’re willing to go down that specific information hole ;)) and the physical layer should mainly be handling packet loss on the connection between those adaptors, transparently to the higher layers that just see that as lower bandwidth than the spec for the adaptors (a spec which is really quite optimistic, IMHO).

        Yeah, a cable with a metal sheaf wired to the GND level (i.e. Cat cable) is going to be way better at higher frequencies and at isolation from noise that two twisted copper wires were the network signal is shared with a different “signal” which whilst generally 50/60Hz (depending on country) can have spikes and noise at other frequencies, so it’s never going to be the same.

        However for example at home right now I can get a reliable 100 Mbit/s over a pair of those adaptors from my router to my PC and the speed limitation is actually (I believe) from my old router not supporting Gigabit Ethernet rather than from the adaptors which are supposed to handle up to 500 Mbit/sec.

        That said and as somebody pointed out, it only works well if the plugs you’re connecting are on the same electrical network, as transversing coils isn’t exactly great for high frequency signals.

        • ramjambamalam@lemmy.ca
          link
          fedilink
          arrow-up
          0
          ·
          1 year ago

          it only works well if the plugs you’re connecting are on the same electrical network, as transversing coils isn’t exactly great for high frequency signals.

          What does “electrical network” mean? Panel? Circuit?

          • Aceticon@lemmy.world
            link
            fedilink
            arrow-up
            0
            ·
            edit-2
            1 year ago

            If two plugs are connected to different circuit breakers, then they’re in different “electrical networks” in this sense: basically for a signal to go from one such plug to the other one it has to transverse both circuit breakers and that means going through coils.

            Coils are inductors, which are electrical elements which have have frequency dependent resistance (in simple terms), with the higher the frequency of a signal the more the resistance they offer to the passing of a signal, and the higher the bandwidth of your data connection the higher the frequency of the signal(s) necessary to transport that data.

              • Aceticon@lemmy.world
                link
                fedilink
                arrow-up
                1
                ·
                1 year ago

                I learned this stuff in a different language so don’t really know the right terminology in English.

                Also I’m from the Electronics side, so for me a “circuit” is something quite different ;)

                • ramjambamalam@lemmy.ca
                  link
                  fedilink
                  arrow-up
                  1
                  ·
                  1 year ago

                  Ah, in home electrical, a circuit generally means the same thing as electronics, but at 120V and around 15A (in North America).

  • intensely_human@lemm.ee
    link
    fedilink
    arrow-up
    1
    ·
    1 year ago

    I always wonder if I’m introducing bad latency by running a 100 ft ethernet cable.

    Then I remind myself it’s the speed of light.

  • Jtres@lemmy.world
    link
    fedilink
    arrow-up
    0
    ·
    1 year ago

    Do y"all not use the magic adapters that you plug in by your router, then by your PC to make a lan cable out of the electric wiring? That improved my cable management so much

    • Pokethat@lemmy.world
      link
      fedilink
      arrow-up
      0
      ·
      1 year ago

      Power over Ethernet adapters have some serious limitations. MoCa adaptors which use existing coaxial connections, even if you have cable internet, can provide greater speed and better latency than Poe. To be honest though, copper ethernet or fiber ethernet or generally the best way to go.

      Drill through the walls or be lazy and run a cable over the roof

  • Wooly@lemmy.world
    link
    fedilink
    arrow-up
    0
    ·
    1 year ago

    Do people not know power line ethernet adapters are a thing? Look if up on Amazon, you just plug one into the wall by your router and one next to your PC. Clean and strong connections.

    • Veltoss@lemmy.world
      link
      fedilink
      arrow-up
      0
      ·
      1 year ago

      What in tarnation is this black magic? I don’t know how I’ve never heard of these before.

      • Wooly@lemmy.world
        link
        fedilink
        arrow-up
        0
        ·
        1 year ago

        They’re good/reliable enough that it’s worth the £20-30 to try a set out. Although like another guy commented bad wall wiring can sometimes have effects if your router is really fast, I get my full 11MBps through my walls easily enough in relatively old housing.

        • stevestevesteve@lemmy.world
          link
          fedilink
          arrow-up
          0
          ·
          1 year ago

          11mbps, even if that’s megabytes not bits, is pretty fuckin slow as far as network speeds today. That’s either 1/100th or 1/10th of gigabit speeds, and a good Ethernet cable can provide well over gigE nowadays

          • Aceticon@lemmy.world
            link
            fedilink
            arrow-up
            0
            ·
            1 year ago

            Which only really matters if your actual internet connection can do the same.

            Or in other words, it depends, so each one should try to get the right solution for their situation.

            • stevestevesteve@lemmy.world
              link
              fedilink
              arrow-up
              0
              ·
              edit-2
              1 year ago

              I didn’t realize that the only thing people used network connections for was Internet connections. Wow thanks for letting me know.

              Lots of ISPs offer way more than 100mbps, many places offer past 1gbps. Even if they don’t, there are many LAN-based things that run even if you don’t know they do. P2p software updates are widespread now. So yeah “it depends” on whether you care about a fast and stable network connection.

              Not to mention, power line is a shared medium, much like wifi, so if you have two computers, kiss even your already slow speeds goodbye

              • Aceticon@lemmy.world
                link
                fedilink
                arrow-up
                0
                arrow-down
                1
                ·
                edit-2
                1 year ago

                First, I suggest you read the last 12 words of my post rather than reacting to your own interpretation of my comment as a personal dig at you.

                Second, Ethernel over Power sharing is only up to the first circuit breaker, whislt WiFi sharing is only limited by metal surfaces, walls and distance.

                This means that in some situations (for example appartments in appartment buildings) EoP “sharing” is entirelly dependent on what devices a person puts on the same electrical network (i.e. the power line branch sharing the same circuit breaker) whilst WiFi is a complete total hellhole of everybody screwing everybody else.

                Further, people sometimes rent the place they live in, not own it and getting permission to run wire along the walls might be impossible whilst investing in improving the landlord’s property by having wire run within the existing paths inside the wall (usually shared with power wire) is usually not exactly smart.

                So Ethernet Over Power is a possible solution that should be considered in light of the situation and used if appropriate or discarded if not.

                Looking at and evaluating the various solutions in light of the context is the Engineering approach to solving problems, so it makes sense to present a possible solution in a public forum when one’s intention is to help others.

                A self-centred “it’s not good in my situation hence it’s shit and anybody who says otherwise is insulting me” take does nothing to help others.

                • stevestevesteve@lemmy.world
                  link
                  fedilink
                  arrow-up
                  1
                  ·
                  1 year ago

                  My original comment was about how slow Ethernet over power was and you claimed that only matters if your internet is faster. There are lots of situations where you’d run cable where that statement isn’t true. If you had said “sure it’s slower but it still works sometimes” that’s a wildly different statement than the equivalent of “speed only matters if it’s the bottleneck to the internet”

                  Power line adapters are usually fairly separated by different circuits, but that’s far from a hard limit. Just because there’s not a reliable connection between two circuits doesn’t mean the medium isn’t shared and interference can’t happen - it is very much like wifi through a cement wall or two.

                  In no way am I personally offended, I just used some sarcasm to show how inane that original statement is; and those kind of statements are everywhere in networking discussions.